Pipe Cutters with cutter wheel and ratchet mechanism. A quick and accurate cutting of
PE, PVC, PP, PEX, PB and PVDF pipes.

Size 1 : OD 6 - 67mm
Size 2 : OD 6 - 76mm
Size 3 : OD 50 - 140mm
Size 4 : OD 100 - 168mm

Two types are available for the cutting and bevelling of plastic pipes:

Model 315: OD 110 up to OD 315 mm

Model 500: OD 180 up to OD 500 mm

With this light transportable machine plastic pipes of polyolefine can be cut right-angled.

Cutting depth appr. 60 mm.

The machine consists of a motorized hand saw, 230 V/2200 W with guide carriage and tensioning chain for each pipe diameter. The tensioning chain is to be put around the pipe and tightened by means of the chain tensioner. The guidance vehicle is applied with the hand circular saw. After turning on the motor the saw is inserted. The pipe is then cut by driving around.

A quick, clean and right-angled cut is the result. Cutting depth up to 60 mm with type 1 and up to 95 mm with type 2.

The easy handling despite a high cutting speed and an optimal safety do make the saw indispensable on each construction site. Chains for standard pipes are available ex warehouse. Special dimensions only on request.

The band saw WIDOS RS 315 in extra-solid design has been developed particularly for the exact cutting of plastic pipes up to OD 315 and meets highest requirements within modern production lines.

The extremely solid saw bow is optimized for operation with low vibration and is driven on precise linear guides. The saw band drive with high torque performance is switched on over a push button and stops appr. 3 seconds after releasing the push button. The complete saw bow is mounted on a high loadable turning device angle indicator and can easily be manually swivelled for up to 45° (67,5° on one side) after being unlocked. The later course of the cut is indicated by a line laser (optional accessory).

The pipe support has an extremely solid design so that even heaviest pieces can be clamped safely and displaced with minimal expenditure of force. The pipe is clamped by means of a clamping belt, an initial adjusting to the pipe dimension is not necessary. Pipe clamping by means of a pneumatic cylinder is possible on request. When using an optional transverse support, a negative radial cut for the fabrication of reduced branches at T- and Y- pieces can be easily performed. The saw bow is mounted on a basic plate, assembling works in the workshop become unnecessary, only the horizontal adjustment by means of adjusting screws has to be carried out.

The sawing installation RS in extra-solid design has been developed particularly for the exact cutting of plastic pipes and meets highest requirements within modern production lines.

The extremely solid saw bow is optimized for a low vibration and belt sparing operation and is driven by hand wheel on precise linear guides. The band drive with high torque performance is equipped with a break so that any after-running after switching off or after pushing the emergency-off button is avoided. The forward feed is secured against saw forces being too high by means of a safety clutch and totally insensitive to the produced cuttings. The complete forward feed unit is mounted on a high loadable live ring and can easily be turned manually for 45° or 67,5° when being unlocked. The band position and the set angle are displayed on digital devices which can be adjusted to zero very easily by means of pneumatic centering devices.

The pipe supports have an extremely solid design and are 1,8 m long on each side so that even heaviest pieces can be clamped safely and displaced on the exchangeable sliding coatings with minimal expenditure of force. Extensions for the pipe supports are available as option. The pipes are clamped by means of a clamping belt over the complete area to be worked, an initial adjusting to the pipe dimension is not necessary. When using an optional transverse support in connection with an integrated turning of the band and a digital display and locking of the position, a negative radial cut for the fabrication of reduced branches at T- and Y- pieces can be easily performed. Due to the solid base of the complete installation, assembling works in the workshop become unnecessary, only the horizontal adjustment by means of adjusting screws has to be carried out.

* With all versions it is possible to move the solid saw bow with a motorized feed on precise linear guides. The digital band index which is included indicates the exact position of the saw band. Attention! This supplement cannot be subsequently built in.